P0108 Acura Manifold Absolute Pressure Sensor Circuit High Voltage

Description

OBD-II Trouble Code Description for P0108 Acura

Manifold Absolute Pressure/Barometric Pressure Circuit High Input

What does this mean?

OBD2 Code P0108 Acura definition:
The MAP (Manifold Absolute Pressure) sensor measures engine manifold negative air pressure. It’s usually a three wire sensor: a ground wire, a 5 volt reference wire from the PCM (Powertrain Control Module) to the MAP sensor, and a signal wire that informs the PCM of the MAP sensor voltage reading as it changes. The higher the engine vacuum, the lower the voltage reading. The voltage should range between about 1 volt (at idle) to about 5 volts (WOT wide open throttle). If the PCM sees the voltage reading from the MAP sensor is greater than 5 Volts, or if the voltage reading is higher than what the PCM considers normal under certain circumstances, a P0108 Acura DTC will set.

Symptoms

Possible sumptoms of OBD code P0108 Acura
MIL (Malfunction Indicator Lamp) will likely be on Engine may run poorly Engine may not run at all Fuel mileage may decrease Presence of black smoke at exhaust

Causes

Possible causes of OBD code P0108 Acura
Bad MAP sensor Leak in vacuum supply line to MAP sensor Engine vacuum leak Short on signal wire to PCM Short on reference voltage wire from PCM Open in ground circuit to MAP Worn engine causing low vacuum

Possible Solutions

A good way to diagnose if the MAP sensor is to blame would be to compare the KOEO (key on engine off) MAP sensor reading on a scan tool with the Barometric pressure reading. They should be the same because they both measure atmospheric pressure. If the MAP reading is greater than 0.5 volt off of the BARO reading, then replacing the MAP sensor would likely fix the problem. Otherwise, start the engine and observe the MAP reading at idle. It should normally be about 1.5 volts (varies according to altitude). a. If it is, the problem is likely intermittent. Check all the vacuum hoses for damage and replace as necessary. You can also try wiggle testing the harness and connector to reproduce the problem. b. If the scan tool MAP reading is more than 4.5 volts, check the actual engine vacuum reading with the engine running. If it is less than 15 or 16 in. Hg, then the PCM is probably not seeing enough vacuum (due to a worn engine, perhaps) for a given operating condition (which causes a higher than normal voltage signal to the PCM) and setting the code. Repair the engine vacuum problem and retest. c. But, if the actual engine vacuum reading is 16 in. Hg or more, then unplug the MAP sensor. The scan tool MAP reading should indicate that there is no voltage present. Check that the ground from the PCM is intact and also that the MAP sensor connector and terminals are tight. If the connection is good, then replace the map sensor. d. However if, with KOEO, & the MAP sensor unplugged, the scan tool shows a voltage reading, then there may be a short in the harness to the MAP sensor. Turn the ignition off. At the PCM unplug connector and remove the MAP signal wire from the connector. Re-attach the PCM connector and see if with KOEO, the scan tool MAP reading shows voltage. If it still does, replace the PCM. If not, check for voltage on the signal wire you just removed from the PCM. If there is voltage on the signal wire, find the short in the harness and repair.

Related Codes

P0105 Acura P0106 Acura P0107 Acura P0109 Acura

The OBD2 Code Information Be Applicable For Acura:

2014 Acura RLX,2014 Acura MDX,2013 Acura SUV-X Concept,2013 Acura RDX,2013 Acura NSX Concept,2013 Acura MDX Concept,2013 Acura ILX Endurance Racer,2013 Acura ILX,2012 Acura TL,2012 Acura RLX Concept,2012 Acura NSX Concept,2012 Acura ILX Street Build Concept,2012 Acura ILX Concept,2011 Acura TSX Sport Wagon,2011 Acura TSX Sedan,2010 Acura ZDX,2010 Acura TSX V6,2010 Acura RDX,2010 Acura MDX,2009 Acura ZDX Concept,2009 Acura TSX,2009 Acura TL,2009 Acura RL,2007 Acura TSX,2007 Acura TL Type-S,2007 Acura TL,2007 Acura RDX,2007 Acura MDX,2007 Acura Advanced Sports Car Concept,2006 Acura RDX Prototype,2006 Acura MD-X Concept,2006 Acura Advanced Sedan Concept,2005 Acura TSX A-Spec Concept,2005 Acura TSX,2005 Acura TL,2005 Acura RSX Type-S,2005 Acura RSX A-Spec Concept,2005 Acura RSX,2005 Acura RL with ASPEC Performance Package,2005 Acura RL ASPEC Concept,2005 Acura RL,2005 Acura RDX Concept,2005 Acura NSX,2005 Acura MDX,2004 Acura TL with ASPEC Performance Package,2004 Acura TL 25 Hours of Thunderhill,2004 Acura RL Prototype,2004 Acura 3.2 TL,2003 Acura TL ASPEC Concept,2003 Acura 3.2 CL Type-S,2002 Acura NSX sketches,2001 Acura NSX-T,2001 Acura Integra

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Acura makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.