Description
OBD-II Trouble Code Description for P0201 Pontiac
Injector Circuit/Open – Cylinder 1
What does this mean?
OBD2 Code P0201 Pontiac definition:
P0201 Pontiac means that the PCM detected a fault in the injector or the wiring to the injector. It monitors the injector and when the injector is activated, the PCM expects to see the voltage pulled “low” or close to zero. When the injector is switched off, the PCM expects to see a voltage that is close to battery voltage or “high”. If it doesn’t see the expected voltage the PCM will set this code. The PCM also monitors resitance in the circuit. If the resistance is excessively low or high it will set this code.
Symptoms
Possible sumptoms of OBD code P0201 Pontiac
The symptoms for this code will likely be a misfire and a rough running engine. Poor acceleration. The MIL will also be illuminated.
Causes
Possible causes of OBD code P0201 Pontiac
The causes could be any of the following: Bad injector. This is usually the cause of this code but doesn’t rule out the possibility of one of the other causes Open in the wiring to the injector Short in the wiring to the injector Bad PCM
Possible Solutions
First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector
The OBD2 Code Information Be Applicable For Pontiac:
2010 Pontiac G8,2009 Pontiac G8,2009 Pontiac G6 ,2009 Pontiac G3,2008 Pontiac G8,2007 Pontiac Solstice SD-290 Concept,2007 Pontiac Solstice GXP,2007 Pontiac G6 GXP Show Car,2006 Pontiac Torrent,2006 Pontiac Solstice,2006 Pontiac Montana SV6,2006 Pontiac GTO,2006 Pontiac G6 GTP Coupe,2006 Pontiac G6 GTP Convertible,2005 Pontiac Vibe GT,2005 Pontiac Montana SV6,2005 Pontiac Grand Prix,2005 Pontiac Grand Am GT Coupe,2005 Pontiac GTO,2005 Pontiac G6 GT,2004 Pontiac Grand Prix GTP,2004 Pontiac Grand Am GXP,2004 Pontiac GTO 5.7,2004 Pontiac GTO,2004 Pontiac Bonneville GXP,2004 Pontiac Aztek Rally,2003 Pontiac Vibe GT,2003 Pontiac Vibe,2003 Pontiac Sunfire Coupe,2003 Pontiac Montana Thunder,2003 Pontiac Grand Prix,2003 Pontiac Grand Am SE Sedan,2003 Pontiac G6 Concept,2003 Pontiac Aztek,2002 Pontiac Sunfire GXP,2002 Pontiac Sunfire American Tuner,2002 Pontiac Solstice Concept,2002 Pontiac REV Concept,2002 Pontiac Grand Prix GXP,2002 Pontiac Grand Prix G-Force Concept,2002 Pontiac Firebird Trans Am Edition,2001 Pontiac Vibe GT,2001 Pontiac Vibe,2001 Pontiac Sunfire HO,2001 Pontiac Sunfire Accessorized,2001 Pontiac Montana,2001 Pontiac Grand Prix
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Pontiac makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.