Pontiac P0341 Camshaft Position Sensor

Description

OBD-II Trouble Code Description for P0341 Pontiac

Camshaft Position Sensor “A” Circuit Range/Performance

What does this mean?

OBD2 Code P0341 Pontiac definition:
This P0341 Pontiac code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor. This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Any time that the signal to the PCM is inconsistent with what the signal should be, this code is set. NOTE: this code can also be set by extended cranking periods.

Symptoms

Possible sumptoms of OBD code P0341 Pontiac
The car will likely run with this code set, as it is often intermittent and also because the PCM can often operate the vehicle in “limp-in/limp-home” mode even with a cam sensor signal problem. There may be no noticeable symptoms other than: Poor fuel economy (if engine runs) Possible no start condition

Causes

Possible causes of OBD code P0341 Pontiac
A code P0341 Pontiac may mean that one or more of the following has happened: Cam sensor wiring routed too close to spark plug wiring (causing interference) Poor wiring connection at cam sensor Poor wiring connection at PCM Bad cam sensor Damaged reluctor wheel

Possible Solutions

Often relacing the sensor fixes this code, but not necessarily. Therefore it’s important to check the following: Check that the wiring isn’t routed too close to any secondary ignition components (coil, spark plug wires, etc.) Visually inspect the wiring at the sensor for any burn marks, discoloration indicative of melting or chafing Visually inspect the cam sensor for damage Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage If reluctor isn’t visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design) If all checks out okay, then replace the sensor. Related Camshaft Trouble Codes: P0340 Pontiac

Related Codes

P0340 Pontiac P0342 Pontiac


The OBD2 Code Information Be Applicable For Pontiac:

2010 Pontiac G8,2009 Pontiac G8,2009 Pontiac G6 ,2009 Pontiac G3,2008 Pontiac G8,2007 Pontiac Solstice SD-290 Concept,2007 Pontiac Solstice GXP,2007 Pontiac G6 GXP Show Car,2006 Pontiac Torrent,2006 Pontiac Solstice,2006 Pontiac Montana SV6,2006 Pontiac GTO,2006 Pontiac G6 GTP Coupe,2006 Pontiac G6 GTP Convertible,2005 Pontiac Vibe GT,2005 Pontiac Montana SV6,2005 Pontiac Grand Prix,2005 Pontiac Grand Am GT Coupe,2005 Pontiac GTO,2005 Pontiac G6 GT,2004 Pontiac Grand Prix GTP,2004 Pontiac Grand Am GXP,2004 Pontiac GTO 5.7,2004 Pontiac GTO,2004 Pontiac Bonneville GXP,2004 Pontiac Aztek Rally,2003 Pontiac Vibe GT,2003 Pontiac Vibe,2003 Pontiac Sunfire Coupe,2003 Pontiac Montana Thunder,2003 Pontiac Grand Prix,2003 Pontiac Grand Am SE Sedan,2003 Pontiac G6 Concept,2003 Pontiac Aztek,2002 Pontiac Sunfire GXP,2002 Pontiac Sunfire American Tuner,2002 Pontiac Solstice Concept,2002 Pontiac REV Concept,2002 Pontiac Grand Prix GXP,2002 Pontiac Grand Prix G-Force Concept,2002 Pontiac Firebird Trans Am Edition,2001 Pontiac Vibe GT,2001 Pontiac Vibe,2001 Pontiac Sunfire HO,2001 Pontiac Sunfire Accessorized,2001 Pontiac Montana,2001 Pontiac Grand Prix

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Pontiac makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.