Description
OBD-II Trouble Code Description for P0453 Pontiac
Evaporative Emission System Pressure Sensor/Switch High
What does this mean?
OBD2 Code P0453 Pontiac definition:
The EVAP (Evaporative Emissions) System allows fuel tank vapors to be purged into the engine and burnt rather than expelled into the atmosphere as harmful emissions. The EVAP system contains a pressure sensor to check the integrity of the system. Periodically, the EVAP system performs a pressure test to check that there are no leaks in the system. It uses this sensor, also known as a fuel tank pressure (FTP) sensor to check for leaks. Basically P0453 Pontiac means the PCM (Powertrain Control Module) noticed the EVAP Pressure sensor or FTP is indicating a higher than normal pressure (above 4.5 Volts) in the EVAP system. NOTE: On some vehicles the FTP is a part of the fuel pump assembly in the tank.
Symptoms
Possible sumptoms of OBD code P0453 Pontiac
There will likely be no noticeable symptoms along with this code other than the MIL (Malfunction Indicator Lamp), commonly known as Check Engine Light illumination. However, there may be noticeable fuel odors in some cases.
Causes
Possible causes of OBD code P0453 Pontiac
A P0453 Pontiac DTC trouble code may be caused by one or more of the following: Open on FTP sensor signal wire Short to voltage on FTP sensor signal wire Bad FTP sensor Abnormally high pressure in fuel tank due to blockage in EVAP purge hoses or overfilled tank Loose/damaged FTP sensor connector Loss of ground to the sensor
Possible Solutions
Using an scan tool access FTP sensor value with Key on Engine off (KOEO). Normal value is usually somewhere near 2.5 Volts at atmospheric pressure (may fluctuate some due to altitude). It shouldn’t ever be above 4.5 Volts. 1) If it is close to 2.7V with the gas cap off, the problem is likely intermittent. Using a Digital Volt Ohm Meter, measure the voltage on the signal wire while trying to induce the problem by wiggle testing all the wiring at the FTP sensor. If the voltage fluctuates when wiggle testing, check for connector problems; i.e. water in the connector, broken or chafed wiring. 2) If the value shown on the scan tool is above 4.5V, unplug the sensor (if possible) and check for voltage again. If the high voltage is still present when unplugged, inspect wiring harness for a short to voltage on the signal wire. If the high voltage disappears when unplugging the sensor, check for a good ground to the sensor and proper reference voltage. If you have a good ground and 5 Volts reference voltage, replace the FTP sensor since it’s likely shorted out.
The OBD2 Code Information Be Applicable For Pontiac:
2010 Pontiac G8,2009 Pontiac G8,2009 Pontiac G6 ,2009 Pontiac G3,2008 Pontiac G8,2007 Pontiac Solstice SD-290 Concept,2007 Pontiac Solstice GXP,2007 Pontiac G6 GXP Show Car,2006 Pontiac Torrent,2006 Pontiac Solstice,2006 Pontiac Montana SV6,2006 Pontiac GTO,2006 Pontiac G6 GTP Coupe,2006 Pontiac G6 GTP Convertible,2005 Pontiac Vibe GT,2005 Pontiac Montana SV6,2005 Pontiac Grand Prix,2005 Pontiac Grand Am GT Coupe,2005 Pontiac GTO,2005 Pontiac G6 GT,2004 Pontiac Grand Prix GTP,2004 Pontiac Grand Am GXP,2004 Pontiac GTO 5.7,2004 Pontiac GTO,2004 Pontiac Bonneville GXP,2004 Pontiac Aztek Rally,2003 Pontiac Vibe GT,2003 Pontiac Vibe,2003 Pontiac Sunfire Coupe,2003 Pontiac Montana Thunder,2003 Pontiac Grand Prix,2003 Pontiac Grand Am SE Sedan,2003 Pontiac G6 Concept,2003 Pontiac Aztek,2002 Pontiac Sunfire GXP,2002 Pontiac Sunfire American Tuner,2002 Pontiac Solstice Concept,2002 Pontiac REV Concept,2002 Pontiac Grand Prix GXP,2002 Pontiac Grand Prix G-Force Concept,2002 Pontiac Firebird Trans Am Edition,2001 Pontiac Vibe GT,2001 Pontiac Vibe,2001 Pontiac Sunfire HO,2001 Pontiac Sunfire Accessorized,2001 Pontiac Montana,2001 Pontiac Grand Prix
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Pontiac makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.