Description
OBD-II Trouble Code Description for P0112 Porsche
Intake Air Temperature Sensor 1 Circuit Low
What does this mean?
OBD2 Code P0112 Porsche definition:
The IAT (intake air temperature) sensor simply measures the temperature of air that is entering the engine. Intake air temperature is important because the higher the intake air, the higher the combustion temperatures. High combustion temperatures result in increased Nox (Nitrogen oxides) emissions. To keep these higher temps from causing increased combustion temps, the intake air tubing should be intact, allowing the engine to “breathe” air that isn’t sampled from the engine compartment. The IAT measures air temp by using a thermistor, or a thermometer of sorts. The thermistor is supplied 5 volts reference voltage from the PCM (powertrain control module) and a ground. Usually, when the air temperature is cold the resistance in the thermistor is high and when the air temperature is warmer, the resistance decreases. This change in resistance changes the 5 V reference from the PCM, thereby informing the PCM of the temperature of incoming air. If the PCM notices that the incoming air temp is unusually high, say, 300 degrees, when the engine temp is still relatively low, it will set a P0112 Porsche.
Symptoms
Possible sumptoms of OBD code P0112 Porsche
There may be no noticeable symptoms of a P0112 Porsche code other than an MIL (Malfunction Indicator Lamp). However, a emissions test may reveal higher Nox readings depending on the type of IAT failure. Or the engine may ping under load, depending on the type of IAT failure.
Causes
Possible causes of OBD code P0112 Porsche
No reference voltage to the IAT sensor due to an open wire Excessively high intake air temperatures Short to ground on signal circuit Damaged IAT connector Bad PCM
Possible Solutions
Hook up your scan tool or code reader and read the IAT reading. With a cold engine, the IAT should roughly match the coolant reading, since both will read ambient temperature. If the IAT is reading excessively high, check the IAT connector for damage. If you find none, unplug the IAT sensor and recheck the reading. It should now read the minimum, around -20 deg. If it does, then replace the IAT sensor. But, if the reading is still high, unplug the sensor and check for resistance across the two wiring harness terminals. If there is infinite resistance, then the PCM itself is bad. If the resistance isn’t infinite, then check and repair the short to ground on the signal circuit.
The OBD2 Code Information Be Applicable For Porsche:
2013 Porsche Cayenne,2013 Porsche Boxster S,2013 Porsche Boxster,2013 Porsche 911,2012 Porsche Panamera,2012 Porsche 911,2011 Porsche 911,2010 Porsche Panamera,2010 Porsche Cayenne,2010 Porsche 911 GT3,2009 Porsche 911,2008 Porsche Cayenne,2008 Porsche Boxster,2008 Porsche 911,2007 Porsche Cayman,2007 Porsche Cayman,2007 Porsche Boxster,2007 Porsche Boxster,2007 Porsche 911,2006 Porsche 911,2005 Porsche Boxster S,2005 Porsche Boxster,2005 Porsche 911,2004 Porsche 911,2003 Porsche 911
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Porsche makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.