Porsche P0335 Crankshaft Position Sensor A Circuit Malfunction

Description

OBD-II Trouble Code Description for P0335 Porsche

Crankshaft Position Sensor “A” Circuit

What does this mean?

OBD2 Code P0335 Porsche definition:
The crankshaft position sensor (CKP) measures crankshaft location and relays this information to the PCM (Powertrain Control Module). Depending on the vehicle, the PCM uses this crankshaft position information to time the spark properly or on some systems it is only for misfire detection and does not control spark timing. The CKP sensor is stationary and works in harmony with a reluctor ring (or toothed ring) that is attached to the crankshaft. As this reluctor ring passes in front of the CKP sensor, the magnetic field created by the CKP sensor is interrupted and this creates a square wave voltage signal that the PCM interprets as crankshaft position. If the PCM detects that there are no crankshaft pulses or if it sees a problem with the pulses on the output circuit, P0335 Porsche will set.

Symptoms

Possible sumptoms of OBD code P0335 Porsche
NOTE: If the crank sensor is used only for misfire detection and NOT spark timing (this varies with the vehicle), the vehicle should start and run with MIL (Malfunction indicator lamp) illumination. Also, some vehicles require several key cycles to illuminate the MIL. If this is the case, there may be no MIL illumination until the problem often enough over time. If the crank sensor is used for BOTH misfire detection and spark timing, the vehicle may or may not start. Symptoms may include: Vehicle may not start (see above) Vehicle may run rough or misfire MIL illumination

Causes

Possible causes of OBD code P0335 Porsche
Damaged CKP sensor connector Damaged reluctor ring (missing teeth or not turning due to sheared-off keyway) Sensor output open Sensor output shorted to ground Sensor output shorted to voltage Failed crank sensor Broken timing belt Failed PCM

Possible Solutions

Using a scan tool, check if, when engine is running or cranking, that there is an RPM signal. If there is no RPM reading, then visually inspect the crank sensor and connector for any damage and repair as necessary. If there is no visible damage, and you have access to a scope, you could check the CKP 5 Volt square wave pattern. If you do not, then, obtain a resistance reading of your crank sensor from a repair manual. (There are so many different types of crank sensors that there’s no way to put here which resistance reading is correct). Then check the resistance of the CKP sensor by disconnecting the sensor and measuring resistance of the sensor. (It is best to check resistance readings from the PCM connector. This rules out any wiring problems from the start. But it does require some mechanical skill and shouldn’t be performed if you’re not familiar with automobile electrical systems). Is the sensor within resistance specs? If not, replace the CKP sensor. If so, recheck resistance reading from the PCM connector. Is the reading still okay? If not, repair open or short in the wiring to the crank sensor and re-check. If the reading is okay, the problem is intermittent or the PCM may be at fault. Try reconnecting and checking for RPM signal again. If there is now an RPM signal, wiggle test the wiring harness to try and induce the fault.

Related Codes

P0385 Porsche P0335 Porsche P0385 Porsche P0016 Porsche P0017 Porsche P0018 Porsche P0019 Porsche P0335 Porsche P0336 Porsche P0337 Porsche P0338 Porsche P0339 Porsche P0385 Porsche P0386 Porsche P0387 Porsche P0388 Porsche P0389 Porsche


The OBD2 Code Information Be Applicable For Porsche:

2013 Porsche Cayenne,2013 Porsche Boxster S,2013 Porsche Boxster,2013 Porsche 911,2012 Porsche Panamera,2012 Porsche 911,2011 Porsche 911,2010 Porsche Panamera,2010 Porsche Cayenne,2010 Porsche 911 GT3,2009 Porsche 911,2008 Porsche Cayenne,2008 Porsche Boxster,2008 Porsche 911,2007 Porsche Cayman,2007 Porsche Cayman,2007 Porsche Boxster,2007 Porsche Boxster,2007 Porsche 911,2006 Porsche 911,2005 Porsche Boxster S,2005 Porsche Boxster,2005 Porsche 911,2004 Porsche 911,2003 Porsche 911

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Porsche makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.