Description
OBD-II Trouble Code Description for P0101 Renault
Mass or Volume Air Flow Circuit Range/Performance
What does this mean?
OBD2 Code P0101 Renault definition:
Basically this means that there is a problem with the Mass Air Flow (MAF) sensor or circuit. The PCM detects that the actual MAF sensor frequency signal is not within a predetermined range of the calculated MAF value for more than 4.0 seconds.
Symptoms
Possible sumptoms of OBD code P0101 Renault
You will likely not notice any serious drivability problems, although there may be symptoms.
Possible Solutions
The simplest thing to do is to reset the code and see if it comes back. Then start with the cheapest, easiest repair procedures: Inspect for the following conditions: An incorrectly routed harness–Inspect the harness of the MAF sensor in order to verify that it is not routed too close to the following components: – The secondary ignition wires or coils – Any solenoids – Any relays – Any motors A low minimum air rate through the sensor bore may cause this DTC to set at idle or during deceleration. Inspect for any vacuum leaks downstream of the MAF sensor. A wide open throttle (WOT) acceleration from a stop should cause the MAF sensor g/s display on the scan tool to increase rapidly. This increase should be from 6-12 g/s at idle to 230 g/s or more at the time of the 1-2 shift. If the increase is not observed, inspect for a restriction in the induction system or the exhaust system. The barometric pressure (BARO) that is used in order to calculate the predicted MAF value is initially based on the MAP sensor at key ON. When the engine is running the MAP sensor value is continually updated near WOT. A skewed MAP sensor will cause the calculated MAF value to be inaccurate. The value shown for the MAP sensor display varies with the altitude. With the ignition ON and the engine OFF, 103 kPa is the approximate value near sea level. This value will decrease by approximately 3 kPa for every 305 meters (1,000 feet) of altitude. A high resistance on the ground circuit of the MAP sensor can cause this DTC to set. Any loss of vacuum to the MAP sensor can cause this DTC to set. If you suspect the condition may be related to aftermarket accessories, refer to Checking Aftermarket Accessories in Wiring Systems.
The OBD2 Code Information Be Applicable For Renault:
2013 Renault ZOE,2013 Renault Twin-Z Concept,2013 Renault Twin-Run Concept,2013 Renault Talisman,2013 Renault Symbol,2013 Renault Scenic XMOD,2013 Renault Fluence,2013 Renault Espace,2013 Renault Clio,2012 Renault Twingo,2011 Renault Megane,2011 Renault Latitude,2011 Renault Laguna Estate,2011 Renault Laguna,2011 Renault Frendzy Concept,2011 Renault Captur Concept,2010 Renault Scenic,2010 Renault Megane RS,2010 Renault Megane Estate,2010 Renault Grand Scenic,2010 Renault Fluence,2010 Renault DeZir Concept,2010 Renault Clio RS,2009 Renault Twingo RS,2009 Renault Symbol,2009 Renault Scenic,2009 Renault Safrane,2009 Renault Megane,2009 Renault Laguna GT,2009 Renault Laguna Coupe,2009 Renault Koleos,2009 Renault Kangoo,2009 Renault Clio Campus,2009 Renault Clio,2008 Renault ZE Concept,2008 Renault Twingo,2008 Renault Sandero,2008 Renault Laguna Estate,2008 Renault Laguna,2008 Renault Kangoo,2007 Renault Megane,2006 Renault Twingo,2006 Renault Thalia,2006 Renault Nepta Concept,2006 Renault Kangoo,2006 Renault Espace,2006 Renault Clio Sport,2006 Renault Clio RS Concept,2006 Renault Altica Concept,2005 Renault Z17 Concept,2005 Renault Vel Satis,2005 Renault Modus Initiale,2005 Renault Laguna,2005 Renault Clio III,2004 Renault Modus,2004 Renault Megane,2004 Renault Clio,2003 Renault Scenic II,2003 Renault Be Bop
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Renault makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.