Description
OBD-II Trouble Code Description for P0112 Renault
Intake Air Temperature Sensor 1 Circuit Low
What does this mean?
OBD2 Code P0112 Renault definition:
The IAT (intake air temperature) sensor simply measures the temperature of air that is entering the engine. Intake air temperature is important because the higher the intake air, the higher the combustion temperatures. High combustion temperatures result in increased Nox (Nitrogen oxides) emissions. To keep these higher temps from causing increased combustion temps, the intake air tubing should be intact, allowing the engine to “breathe” air that isn’t sampled from the engine compartment. The IAT measures air temp by using a thermistor, or a thermometer of sorts. The thermistor is supplied 5 volts reference voltage from the PCM (powertrain control module) and a ground. Usually, when the air temperature is cold the resistance in the thermistor is high and when the air temperature is warmer, the resistance decreases. This change in resistance changes the 5 V reference from the PCM, thereby informing the PCM of the temperature of incoming air. If the PCM notices that the incoming air temp is unusually high, say, 300 degrees, when the engine temp is still relatively low, it will set a P0112 Renault.
Symptoms
Possible sumptoms of OBD code P0112 Renault
There may be no noticeable symptoms of a P0112 Renault code other than an MIL (Malfunction Indicator Lamp). However, a emissions test may reveal higher Nox readings depending on the type of IAT failure. Or the engine may ping under load, depending on the type of IAT failure.
Causes
Possible causes of OBD code P0112 Renault
No reference voltage to the IAT sensor due to an open wire Excessively high intake air temperatures Short to ground on signal circuit Damaged IAT connector Bad PCM
Possible Solutions
Hook up your scan tool or code reader and read the IAT reading. With a cold engine, the IAT should roughly match the coolant reading, since both will read ambient temperature. If the IAT is reading excessively high, check the IAT connector for damage. If you find none, unplug the IAT sensor and recheck the reading. It should now read the minimum, around -20 deg. If it does, then replace the IAT sensor. But, if the reading is still high, unplug the sensor and check for resistance across the two wiring harness terminals. If there is infinite resistance, then the PCM itself is bad. If the resistance isn’t infinite, then check and repair the short to ground on the signal circuit.
The OBD2 Code Information Be Applicable For Renault:
2013 Renault ZOE,2013 Renault Twin-Z Concept,2013 Renault Twin-Run Concept,2013 Renault Talisman,2013 Renault Symbol,2013 Renault Scenic XMOD,2013 Renault Fluence,2013 Renault Espace,2013 Renault Clio,2012 Renault Twingo,2011 Renault Megane,2011 Renault Latitude,2011 Renault Laguna Estate,2011 Renault Laguna,2011 Renault Frendzy Concept,2011 Renault Captur Concept,2010 Renault Scenic,2010 Renault Megane RS,2010 Renault Megane Estate,2010 Renault Grand Scenic,2010 Renault Fluence,2010 Renault DeZir Concept,2010 Renault Clio RS,2009 Renault Twingo RS,2009 Renault Symbol,2009 Renault Scenic,2009 Renault Safrane,2009 Renault Megane,2009 Renault Laguna GT,2009 Renault Laguna Coupe,2009 Renault Koleos,2009 Renault Kangoo,2009 Renault Clio Campus,2009 Renault Clio,2008 Renault ZE Concept,2008 Renault Twingo,2008 Renault Sandero,2008 Renault Laguna Estate,2008 Renault Laguna,2008 Renault Kangoo,2007 Renault Megane,2006 Renault Twingo,2006 Renault Thalia,2006 Renault Nepta Concept,2006 Renault Kangoo,2006 Renault Espace,2006 Renault Clio Sport,2006 Renault Clio RS Concept,2006 Renault Altica Concept,2005 Renault Z17 Concept,2005 Renault Vel Satis,2005 Renault Modus Initiale,2005 Renault Laguna,2005 Renault Clio III,2004 Renault Modus,2004 Renault Megane,2004 Renault Clio,2003 Renault Scenic II,2003 Renault Be Bop
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Renault makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.