Description
OBD-II Trouble Code Description for P0121 Renault
Throttle/Pedal Position Sensor/Switch “A” Circuit Range/Performance
What does this mean?
OBD2 Code P0121 Renault definition:
The Throttle position sensor is a potentiometer that measures the amount of throttle opening. As the throttle is opened, the reading (measured in volts) goes up. The powertrain control module (PCM) supplies a 5 Volt reference signal to the throttle position sensor (TPS) and usually a ground also. A general measurement is: at idle = .5 Volts; full throttle = 4.5 Volts. If the PCM detects that the throttle angle is greater or less than it should be for a specific RPM, it will set this code.
Symptoms
Possible sumptoms of OBD code P0121 Renault
Symptoms of a P0121 Renault trouble code could include: Malfunction Indicator Lamp (MIL) illumination (Check Engine Light or Service Engine Soon light) Intermittent stumble on acceleration or deceleration Blows black smoke on acceleration No start
Causes
Possible causes of OBD code P0121 Renault
A code P0121 Renault may mean that one or more of the following has happened: TPS has intermittent open or short internally Harness is rubbing and causing an open or short in the wiring Bad connection at the TPS Bad PCM (less likely) Water or corrosion in connector or sensor
Possible Solutions
1. If you have access to a scan tool, see what the idle and WOT (wide open throttle) readings are for the TPS. Check if they’re close to the specifications mentioned above. If not, then replace the TPS and re-check. 2. Check for an intermittent open or short in the TPS signal. To do that, you can’t use a scan tool. You’ll need an oscilliscope. The reason is because scan tools take samplings of many different readings over just one or two data lines and can miss an intermittent drop out. Hook up your oscilliscope and watch the signal. It should sweep up and down smoothly with no drop outs or spikes. 3. If no problems were noticed, perform a wiggle test. Do this by wiggling the connector and harness while watching the pattern. Does it drop out? If so, replace TPS and re-check. 4. If you have no TPS signal, check for 5 Volt reference at the connector. If it’s present, check the ground circuit for open or shorts. 5. Make sure the signal circuit isn’t 12V. It should never have battery voltage. If it does, trace circuit for short to voltage and repair. 6. Look for any water in the connector and replace TPS as necessary.
The OBD2 Code Information Be Applicable For Renault:
2013 Renault ZOE,2013 Renault Twin-Z Concept,2013 Renault Twin-Run Concept,2013 Renault Talisman,2013 Renault Symbol,2013 Renault Scenic XMOD,2013 Renault Fluence,2013 Renault Espace,2013 Renault Clio,2012 Renault Twingo,2011 Renault Megane,2011 Renault Latitude,2011 Renault Laguna Estate,2011 Renault Laguna,2011 Renault Frendzy Concept,2011 Renault Captur Concept,2010 Renault Scenic,2010 Renault Megane RS,2010 Renault Megane Estate,2010 Renault Grand Scenic,2010 Renault Fluence,2010 Renault DeZir Concept,2010 Renault Clio RS,2009 Renault Twingo RS,2009 Renault Symbol,2009 Renault Scenic,2009 Renault Safrane,2009 Renault Megane,2009 Renault Laguna GT,2009 Renault Laguna Coupe,2009 Renault Koleos,2009 Renault Kangoo,2009 Renault Clio Campus,2009 Renault Clio,2008 Renault ZE Concept,2008 Renault Twingo,2008 Renault Sandero,2008 Renault Laguna Estate,2008 Renault Laguna,2008 Renault Kangoo,2007 Renault Megane,2006 Renault Twingo,2006 Renault Thalia,2006 Renault Nepta Concept,2006 Renault Kangoo,2006 Renault Espace,2006 Renault Clio Sport,2006 Renault Clio RS Concept,2006 Renault Altica Concept,2005 Renault Z17 Concept,2005 Renault Vel Satis,2005 Renault Modus Initiale,2005 Renault Laguna,2005 Renault Clio III,2004 Renault Modus,2004 Renault Megane,2004 Renault Clio,2003 Renault Scenic II,2003 Renault Be Bop
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Renault makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.