Description
OBD-II Trouble Code Description for P0453 Renault
Evaporative Emission System Pressure Sensor/Switch High
What does this mean?
OBD2 Code P0453 Renault definition:
The EVAP (Evaporative Emissions) System allows fuel tank vapors to be purged into the engine and burnt rather than expelled into the atmosphere as harmful emissions. The EVAP system contains a pressure sensor to check the integrity of the system. Periodically, the EVAP system performs a pressure test to check that there are no leaks in the system. It uses this sensor, also known as a fuel tank pressure (FTP) sensor to check for leaks. Basically P0453 Renault means the PCM (Powertrain Control Module) noticed the EVAP Pressure sensor or FTP is indicating a higher than normal pressure (above 4.5 Volts) in the EVAP system. NOTE: On some vehicles the FTP is a part of the fuel pump assembly in the tank.
Symptoms
Possible sumptoms of OBD code P0453 Renault
There will likely be no noticeable symptoms along with this code other than the MIL (Malfunction Indicator Lamp), commonly known as Check Engine Light illumination. However, there may be noticeable fuel odors in some cases.
Causes
Possible causes of OBD code P0453 Renault
A P0453 Renault DTC trouble code may be caused by one or more of the following: Open on FTP sensor signal wire Short to voltage on FTP sensor signal wire Bad FTP sensor Abnormally high pressure in fuel tank due to blockage in EVAP purge hoses or overfilled tank Loose/damaged FTP sensor connector Loss of ground to the sensor
Possible Solutions
Using an scan tool access FTP sensor value with Key on Engine off (KOEO). Normal value is usually somewhere near 2.5 Volts at atmospheric pressure (may fluctuate some due to altitude). It shouldn’t ever be above 4.5 Volts. 1) If it is close to 2.7V with the gas cap off, the problem is likely intermittent. Using a Digital Volt Ohm Meter, measure the voltage on the signal wire while trying to induce the problem by wiggle testing all the wiring at the FTP sensor. If the voltage fluctuates when wiggle testing, check for connector problems; i.e. water in the connector, broken or chafed wiring. 2) If the value shown on the scan tool is above 4.5V, unplug the sensor (if possible) and check for voltage again. If the high voltage is still present when unplugged, inspect wiring harness for a short to voltage on the signal wire. If the high voltage disappears when unplugging the sensor, check for a good ground to the sensor and proper reference voltage. If you have a good ground and 5 Volts reference voltage, replace the FTP sensor since it’s likely shorted out.
The OBD2 Code Information Be Applicable For Renault:
2013 Renault ZOE,2013 Renault Twin-Z Concept,2013 Renault Twin-Run Concept,2013 Renault Talisman,2013 Renault Symbol,2013 Renault Scenic XMOD,2013 Renault Fluence,2013 Renault Espace,2013 Renault Clio,2012 Renault Twingo,2011 Renault Megane,2011 Renault Latitude,2011 Renault Laguna Estate,2011 Renault Laguna,2011 Renault Frendzy Concept,2011 Renault Captur Concept,2010 Renault Scenic,2010 Renault Megane RS,2010 Renault Megane Estate,2010 Renault Grand Scenic,2010 Renault Fluence,2010 Renault DeZir Concept,2010 Renault Clio RS,2009 Renault Twingo RS,2009 Renault Symbol,2009 Renault Scenic,2009 Renault Safrane,2009 Renault Megane,2009 Renault Laguna GT,2009 Renault Laguna Coupe,2009 Renault Koleos,2009 Renault Kangoo,2009 Renault Clio Campus,2009 Renault Clio,2008 Renault ZE Concept,2008 Renault Twingo,2008 Renault Sandero,2008 Renault Laguna Estate,2008 Renault Laguna,2008 Renault Kangoo,2007 Renault Megane,2006 Renault Twingo,2006 Renault Thalia,2006 Renault Nepta Concept,2006 Renault Kangoo,2006 Renault Espace,2006 Renault Clio Sport,2006 Renault Clio RS Concept,2006 Renault Altica Concept,2005 Renault Z17 Concept,2005 Renault Vel Satis,2005 Renault Modus Initiale,2005 Renault Laguna,2005 Renault Clio III,2004 Renault Modus,2004 Renault Megane,2004 Renault Clio,2003 Renault Scenic II,2003 Renault Be Bop
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Renault makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.