Description
OBD-II Trouble Code Description for P0208 Saab
Injector Circuit/Open – Cylinder 8
What does this mean?
OBD2 Code P0208 Saab definition:
P0207 Saab means that the PCM detected a fault in the injector or the wiring to the injector. It monitors the injector and when the injector is activated, the PCM expects to see the voltage pulled “low” or close to zero. When the injector is switched off, the PCM expects to see a voltage that is close to battery voltage or “high”. If it doesn’t see the expected voltage the PCM will set this code. The PCM also monitors resitance in the circuit. If the resistance is excessively low or high it will set this code.
Symptoms
Possible sumptoms of OBD code P0208 Saab
The symptoms for this code will likely be a misfire and a rough running engine. Poor acceleration. The MIL will also be illuminated.
Causes
Possible causes of OBD code P0208 Saab
The causes of a P0207 Saab engine light code could be any of the following: Bad injector. This is usually the cause of this code but doesn’t rule out the possibility of one of the other causes Open in the wiring to the injector Short in the wiring to the injector Bad PCM
Possible Solutions
First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector First, using a DVOM check the resistance of the injector. If it isn’t within specs, then replace the injector. Check for voltage at the fuel injector connector. It should have 10 volts or more. Visually check the connector for damage or broken wires. Visually check the injector for damage. If you have access to an injector tester, activate the injector and see if it operates. If the injector operates, then you likely have either an open in the wiring, or a blocked injector. If you do not have access to a tester, swap the injector with another one and see if the code changes. If the code changes, then change the injector. At the PCM, remove the driver wire from the PCM connector and Ground the wire. (Make sure you have the correct wire. If you’re not sure, do not attempt) The injector should activate Replace the injector
The OBD2 Code Information Be Applicable For Saab:
2012 Saab 9-5,2012 Saab 9-4X,2011 Saab PhoeniX Concept,2010 Saab 9-5 Sedan,2010 Saab 9-3,2010 Saab 9-3X,2008 Saab Turbo X,2008 Saab 9-X,2008 Saab 9-7X,2008 Saab 9-4X,2008 Saab 9-3,2008 Saab 9-3,2008 Saab 9-3,2006 Saab 9-7X,2006 Saab 9-5,2006 Saab 9-3,2005 Saab 9-5,2005 Saab 9-3,2005 Saab 9-2,2003 Saab 95,2003 Saab 93
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Saab makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.