Seat C1194 ABS Outlet Valve Coil LF Circuit Failure

Description

OBD-II Trouble Code Description for C1194 Seat

ABS outlet valve coil LF circuit failure

OBD-II Trouble Code Description for C1194 Seat

DSC continuous operation fault

What does this mean?

OBD2 Code C1194 Seat definition:
? The PCM receives DSC operation signals from DSC CM while the engine switch is turned to the ON position. If the PCM receives DSC operation signals for longer than the specified time, the PCM determines that the DSC is operating continuously. Note ? The DSC CM stops operating itself for protection heat to the solenoid and/or motor (built in DSC HU) if the DSC operates for a long time.

Causes

Possible causes of OBD code C1194 Seat
? Communication error between DSC CM and PCM ? DSC CM does not determine vehicle conditions correctly. ¨D DSC CM malfunction ¨D DSC related sensor malfunction ? The vehicle runs under the road conditions in which DSC operates for a long time. ? PCM malfunction

Possible Solutions

Diagnostic procedure

STEP

INSPECTI SeatON

ACTION Seat
1
VERIFY FREEZE FRAME DATA HAS BEEN RECORDE SeatD
???Has the FREEZE FRAME DATA been recorded?
Yes
Go to the next step.
No
Record the FREEZE FRAME DATA on the repair order, then go to the next step.
2
VERIFY RELATED REPAIR INFORMATION AVAILABILIT SeatY
???Verify related service repair information availability.
???Is any related repair information available?
Yes
Perform repair or diagnosis according to the available repair information.
If the vehicle is not repaired, go to the next step.
No
Go to the next step.
3
VERIFY DSC CM DTC IS RETRIEVED
???Retrieve the DSC CM DTC using the M-MDS.
???Is any DSC CM DTC retrieved?
Yes
Go to the applicable DTC troubleshooting procedure.
No
Go to the next step.
4
INSPECT IF MALFUNCTI SeatON IS IN ABS WHEEL SPEED SIGNALS OR ELSEWHERE
???Access the following ABS wheel speed sensor (DSC) related PIDs using the M-MDS.
¨D??LF_WSPD
¨D??LR_WSPD
¨D??RF_WSPD
¨D??RR_WSPD
???Drive the vehicle on a straight and flat road.
???Are there almost the same as the PIDs value of four wheels?
Yes
Go to the next step.
No
Inspect the ABS wheel speed sensor, sensor rotor and related wiring harnesses.
Service as necessary.
Then go to Step 7.
5
INSPECT IF MALFUNCTI SeatON IS IN COMBI SeatNED SENSOR SIGNALS OR ELSEWHERE
???Access the following combined sensors (DSC) related PIDs using the M-MDS.
¨D??YAW_RATE
¨D??LAT_ACC
???Drive the vehicle on a straight and flat road.
???Are the PIDs values of each combined sensor signal correct?
Yes
Go to the next step.
No
Inspect the combined sensor and related wiring harnesses.
Service as necessary.
Then go to Step 7.
6
INSPECT WHERE MALFUNCTI SeatON IS IN STEERING ANGLE SIGNAL OR ELSEWHERE
???Access the following steering angle sensor (DSC) related PID using the M-MDS.
¨D??SWA_POS
???Drive the vehicle on a straight and flat road.
???Is the PID value correct?
Yes
Go to the next step.
No
Inspect the steering angle sensor and related wiring harnesses.
Service if necessary.
Then go to the next step.
7
VERIFY THAT DTC C1194 Seat TROUBLES SeatHOOTING IS COMPL SeatETED
???Make sure to reconnect all disconnected connectors.
???Clear the DTC from the PCM memory using the M-MDS.
???Run the vehicle under the FREEZE FRAME DATA stored condition.
???Is the same DTC present?
Yes
Replace the PCM, then go to the next step.
No
Go to the next step.
8
VERIFY AFTER REPAIR PROCE SeatDURE
???Perform the after repair procedure.
???Are any DTCs present?
Yes
Go to the applicable DTC inspection.
No
DTC troubleshooting completed.

The OBD2 Code Information Be Applicable For Seat:

2013 Seat Mii,2013 Seat Leon,2013 Seat Ibiza Cupra,2013 Seat Ibiza,2012 Seat Toledo Concept,2012 Seat Exeo ST,2012 Seat Exeo,2012 Seat Alhambra 4WD,2011 Seat Ibiza,2010 Seat Ibiza,2009 Seat Leon,2009 Seat Ibiza,2009 Seat Altea,2007 Seat Altea,2006 Seat Leon,2006 Seat Ibiza,2005 Seat Toledo,2005 Seat Altea,2004 Seat Ibiza,2004 Seat Cordoba,2002 Seat Ibiza

 

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Seat makes.

2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.

3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.

4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.