Subaru P0350 Ignition Coil Primary/Secondary Circuit

Description

OBD-II Trouble Code Description for P0350 Subaru

Ignition Coil Primary/Secondary Circuit

What does this mean?

OBD2 Code P0350 Subaru definition:
The ignition signal from the Powertrain Control Module (PCM) or Electronic Control Module(ECM) is sent to and amplified by the power transistor. The power transistor turns ON and OFF the ignition coil primary circuit. This ON/OFF operation induces the proper high voltage in the coil secondary circuit.

Symptoms

Possible sumptoms of OBD code P0350 Subaru
– Engine Light ON (or Service Engine Soon Warning Light) – Lack/Loss of Power – The engine may be harder to start – Engine hesitation

Causes

Possible causes of OBD code P0350 Subaru
– Open or short in the ignition coil circuit – Ignition coil circuit shorted to ground – Ignition coil connector – Damaged ignition coil – Damaged PCM or Possible solution- If damage, repair ignition coil circuit – Replaced ignition coil – Replaced PCM or ECMWhen is the code detected?The test fails when the Powertrain Control Module (PCM) or Electronic Control Module(ECM) does not receive a valid pulse signal from the ignition coil.P0350 Subaru DescriptionThe ignition signal from the Powertrain Control Module (PCM) or Electronic Control Module(ECM) is sent to and amplified by the power transistor. The power transistor turns ON and OFF the ignition coil primary circuit. This ON/OFF operation induces the proper high voltage in the coil secondary circuit. Need more help? or P0350 Subaru – How common is the P0350 Subaru code?Compared to other OBDII codes on Engine-Codes.com in terms of views. NotVery 24/100 Please enable JavaScript to view the OBD2 Codes Comments Powered by Disqus. OBD Engine Codes Comments Powered by Disqus The Error code is generally activated on detection of the following conditions: The test fails when the Powertrain Control Module (PCM) or Electronic Control Module(ECM) does not receive a valid pulse signal from the ignition coil.

Possible Solutions

– If damage, repair ignition coil circuit – Replaced ignition coil – Replaced PCM or ECM


The OBD2 Code Information Be Applicable For Subaru:

2013 Subaru WRX Concept,2013 Subaru Viziv Concept,2013 Subaru Outback,2013 Subaru Legacy,2013 Subaru Impreza,2013 Subaru BRZ,2012 Subaru XV,2012 Subaru Impreza,2011 Subaru XV Concept,2011 Subaru Outback,2011 Subaru Impreza,2011 Subaru Forester,2010 Subaru Legacy,2010 Subaru Impreza,2009 Subaru Impreza,2008 Subaru Impreza,2008 Subaru Forester,2006 Subaru Impreza,2005 Subaru R1,2005 Subaru Pleo,2004 Subaru Impreza,2004 Subaru Forester,2003 Subaru Traviq

Note:

1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Subaru makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.

5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.