Description
OBD-II Trouble Code Description for P0441 Subaru
Evaporative Emission System Incorrect Purge Flow
What does this mean?
OBD2 Code P0441 Subaru definition:
This indicates that a part of the EVAP control system is no longer fuctioning correctly. The EVAP system consists of many parts, including (but not limited to) the gas cap, fuel lines, carbon canister, purge valve, and other hoses. The (EVAP) emission control system prevents the escape of fuel vapors from a vehicle’s fuel system. Fuel vapors are routed by hoses to a charcoal canister for storage. Later, when the engine is running a purge control valve opens allowing intake vacuum to siphon the fuel vapors into the engine. EVAP emission canister purge is contolled by a valve which allows engine vacuum to pull stored fuel vapors from fuel tank into the engine to be burned, rather than be vented to atmosphere. A vacuum switch is used to detect when flow exists. If the PCM commands purge and sees that the switch is closed (indicating no detected purge flow) P0441 Subaru is set.
Symptoms
Possible sumptoms of OBD code P0441 Subaru
Likely, no symptoms will be discernible to the driver, other than the illuminated Check Engine Light.
Causes
Possible causes of OBD code P0441 Subaru
A code P0441 Subaru could mean one or more of the following has happened: Bad vacuum switch Broken or damaged EVAP line or canister Open in PCM purge command circuit Open or short in Voltage feed circuit to Purge Solenoid Faulty purge solenoid Restriction in EVAP solenoid, line or canister Corrosion or resistance in purge connector Bad PCM
Possible Solutions
With a P0441 Subaru OBD-II trouble code, diagnosis can be tricky at times. Here are some things to try: Common Chrysler fix – Replace Leak Detection Pump / LDP Repair damaged EVAP lines or canister Repair open or short in voltage feed circuit to Purge Solenoid Repair open in PCM purge command circuit Replace purge Solenoid Replace vacuum switch Repair restriction in Evap line or canister or soleniod Repair resistance in purge connector Replace PCM
The OBD2 Code Information Be Applicable For Subaru:
2013 Subaru WRX Concept,2013 Subaru Viziv Concept,2013 Subaru Outback,2013 Subaru Legacy,2013 Subaru Impreza,2013 Subaru BRZ,2012 Subaru XV,2012 Subaru Impreza,2011 Subaru XV Concept,2011 Subaru Outback,2011 Subaru Impreza,2011 Subaru Forester,2010 Subaru Legacy,2010 Subaru Impreza,2009 Subaru Impreza,2008 Subaru Impreza,2008 Subaru Forester,2006 Subaru Impreza,2005 Subaru R1,2005 Subaru Pleo,2004 Subaru Impreza,2004 Subaru Forester,2003 Subaru Traviq
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Subaru makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.