Description
OBD-II Trouble Code Description for P0607 Subaru
Control Module Performance
What does this mean?
OBD2 Code P0607 Subaru definition:
This code basically means that the programming of the PCM/ECM (powertrain/engine control module) has failed. This can be a more serious code and may also be refered to as “ECM Internal Circuit Malfunction”.
Symptoms
Possible sumptoms of OBD code P0607 Subaru
The P0607 Subaru code will illuminate the MIL (Malfunction Indicator Lamp). Other potential symptoms of a P0607 Subaru include: vehicle may also go into “limp-home” mode where it runs under reduced power No Start condition (cranks but does not start) may stop running while driving
Causes
Possible causes of OBD code P0607 Subaru
A P0607 Subaru could be caused by one or more of the following: Loose ground terminal on PCM/ECM Dead or defective (12V main) battery An open or short in the power or ground circuit Loose or corroded battery terminals Failed PCM/ECM
Possible Solutions
As a vehicle owner there isn’t a whole lot you can do yourself to diagnose this DTC. The first thing to check is the battery, check the voltage, inspect for loose/corroded terminals, etc., do a load test on it too. Also inspect the grounds/wiring at the PCM. If that’s good the other common fixes for a P0607 Subaru Control Module Performance DTC seem to be either replace the PCM or update (re-flash) the PCM with updated software. Be sure to check for TSB’s on your vehicle (Technical Service Bulletins) as there are known TSB’s for this P0607 Subaru code for some Toyota and Ford vehicles. P0607 Subaru Control Module Performanc If the PCM needs replacement, we strongly recommend you have a qualified repair shop / technician do the work, one that has the capability to reprogram the new PCM. Installing the new PCM may involve using special tools to program the vehicle’s VIN (vehicle identification number) and/or anti-theft information (PATS, etc.). NOTE: This repair may be covered under the emissions warranty so be sure to check with your dealer as this may be covered beyond the bumper-to-bumper or powertrain warranty period.
The OBD2 Code Information Be Applicable For Subaru:
2013 Subaru WRX Concept,2013 Subaru Viziv Concept,2013 Subaru Outback,2013 Subaru Legacy,2013 Subaru Impreza,2013 Subaru BRZ,2012 Subaru XV,2012 Subaru Impreza,2011 Subaru XV Concept,2011 Subaru Outback,2011 Subaru Impreza,2011 Subaru Forester,2010 Subaru Legacy,2010 Subaru Impreza,2009 Subaru Impreza,2008 Subaru Impreza,2008 Subaru Forester,2006 Subaru Impreza,2005 Subaru R1,2005 Subaru Pleo,2004 Subaru Impreza,2004 Subaru Forester,2003 Subaru Traviq
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Subaru makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.