P0117 MAZDA Engine Coolant Temperature Circuit Low Input

Possible causes – Low engine coolant level– Faulty Engine Coolant Temperature (ECT) sensor– Faulty engine coolant thermostat– Engine Coolant Temperature (ECT) sensor harness is open or shorted– Engine Coolant Temperature (ECT) sensor circuit poor electrical connection When is the obd code mean? An excessively low voltage from the sensor is sent to ECM. Symptoms –…

P0116 MAZDA Engine Coolant Temperature Circuit Range/Performance Problem

Possible causes – Low engine coolant level– Faulty Engine Coolant Temperature (ECT) sensor– Faulty engine coolant thermostat– Engine Coolant Temperature (ECT) sensor harness is open or shorted– Engine Coolant Temperature (ECT) sensor circuit poor electrical connection When is the obd code mean? Coolant temperature signal sent to the ngine Control Module (ECM) is not within…

P0118 MAZDA Engine Coolant Temperature Circuit High Input

Possible causes – Low engine coolant level– Faulty Engine Coolant Temperature (ECT) sensor– Faulty engine coolant thermostat– Engine Coolant Temperature (ECT) sensor harness is open or shorted– Engine Coolant Temperature (ECT) sensor electrical circuit poor connection When is the obd code mean? An excessively high voltage from the sensor is sent to ECM. Symptoms –…

P0119 MAZDA Engine Coolant Temperature Signal Intermittent

Possible causes – Low engine coolant level– Faulty Engine Coolant Temperature (ECT) sensor– Faulty engine coolant thermostat– Engine Coolant Temperature (ECT) sensor harness is open or shorted– Engine Coolant Temperature (ECT) sensor electrical circuit poor connection When is the obd code mean? The Engine Control Module (ECM) detected an erratic signal from the engine Coolant…

P0125 MAZDA Excessive Time to Enter Closed Loop Fuel Control

Possible causes – Low engine coolant level– Leaking or stuck open thermostat– Faulty Engine Coolant Temperature (ECT) sensor– Engine Coolant Temperature (ECT) sensor harness is open or shorted– Engine Coolant Temperature (ECT) sensor electrical circuit poor connection When is the obd code mean? The voltage sent to Engine Control Module (ECM) from the Engine Coolant…

P0126 MAZDA Coolant Thermostat Condition Low Operating Temperature

Possible causes – Low engine coolant level– Leaking or stuck open thermostat– Faulty Engine Coolant Temperature (ECT) sensor– Engine Coolant Temperature (ECT) sensor harness is open or shorted– Engine Coolant Temperature (ECT) sensor electrical circuit poor connection When is the obd code mean? The voltage sent to Engine Control Module (ECM) from the sensor is…

P0298 MAZDA Engine Oil Protection Strategy Enabled

Possible causes – Low or dirty motor oil condition– Faulty Oil Pressure Switch– Faulty Engine Oil Temperature (EOT) sensor– Engine overheating condition– Very high engine RPM for an extended period of time Tech description On engines which are equipped with an oil temperature sensor, the Engine Control Module (ECM) reads oil temperature to determine if…

P1132 MAZDA HO2S11 Rich Condition

Possible causes – Leaking injector, regulator or excessive fuel pressure– Engine vacuum leak or open EGR valve at idle– Engine mechanical condition– Faulty HO2S or Mass Air Flow (MAF) sensor Symptoms – Engine Light ON (or Service Engine Soon Warning Light) P1132 MAZDA OBD Code Description A Heated Exhaust Oxygen (HO2S) sensor indicating rich at…

P0128 MAZDA Coolant Thermostat Malfunction

Possible causes – Leaking or stuck open thermostat– Low engine coolant level– Insufficient warm up time– Faulty engine coolant temperature sensor– Engine coolant temperature sensor harness is open or shorted– Engine coolant temperature sensor circuit poor electrical connection Tech description There is a service bulletin for the following Mazda models: 2004-2005 Mazda3 vehicles2006-2007 Mazda5 vehiclesMazda…

P0604 MAZDA ECM RAM error

Possible causes – Loose or poor battery terminal connection– Low battery charge– ECM power supply circuit is open or shorted– ECM Programing– Faulty ECM Tech description Check the ECM fuse, if fuse is OK try erasing the code first and if the code comes back you may have to reprogram or replaced the ECM. When…