Description
OBD-II Trouble Code Description for P0107 Volkswagen
Manifold Absolute Pressure/Barometric Pressure Circuit Low Input
What does this mean?
OBD2 Code P0107 Volkswagen definition:
The Manifold Absolute Pressure (MAP) sensor responds to changes in the intake manifold pressure (vacuum). 5 Volts is supplied to the sensor from the PCM (powertrain control module). Inside the MAP sensor is a resistor that moves in relation to manifold pressure. The resistor varies the voltage between about 1 volt to 4.5 volts (depending on engine load) and that voltage signal is returned to the PCM to indicate manifold pressure (vacuum). This signal is essential for the PCM to determine fuel delivery. A P0107 Volkswagen DTC is set when the PCM sees that the MAP signal voltage is less than .25 volts which is too low.
Symptoms
Possible sumptoms of OBD code P0107 Volkswagen
Anytime the MAP sensor signal is low the vehicle will likely have a very difficult time starting. Other symptoms may include: Hard to start Long cranking times Sputtering/missing Blowing black smoke Poor fuel economy Dies intermittently MIL(Malfunction Indicator Lamp) illumination
Causes
Possible causes of OBD code P0107 Volkswagen
Bad MAP sensor Open or short in the signal circuit Open or short in the 5 Volt reference circuit Ground circuit open or shorted Bad PCM
Possible Solutions
First, using a scan tool with the Key on and engine running, monitor the MAP sensor voltage. If it is reading less than .5 volts, turn engine off, unplug the MAP sensor and, using a DVOM (Digital Volt/Ohm Meter) check for 5Volts on the 5 Volt reference circuit. 1. If there is not 5 Volts on the reference circuit, then check for the reference voltage at the PCM connector. If it is present at the PCM connector but not the MAP connector, repair the open in the reference circuit between the PCM and MAP harness connector. If 5 Volt reference is NOT present at the PCM connector, check powers and grounds of PCM and repair/replace as needed. (NOTE: On Chrysler products, a shorted Crank sensor, Vehicle speed sensor or any other sensor that utilizes the 5 Volt reference from the PCM can short out the 5 Volt reference. To fix simply unplug each sensor one at a time until the 5 Volt reference reappears. The last sensor unplugged is the shorted sensor.) 2. If you have a 5 Volt reference at the MAP connector, jumper the 5 volt reference circuit to the signal circuit. Now check the MAP voltage on the scan tool. It should be 4.5 to 5 Volts. If it is, replace MAP sensor. If not, repair open/short in the signal circuit wiring and re-check. 3. If all appears okay, perform a wiggle test. Start engine and manipulate the harness, connector and tap on the MAP sensor. Note any changes in voltage or engine speed. Repair connector, harness, or sensor as needed. 4. If the wiggle test checks out, use a vacuum pump (or just use your lungs) to draw a vacuum on the MAP sensor vacuum port. As you add vacuum the voltage should decrease. With no vacuum, the MAP sensor should read approximately 4.5 volts. If there is no change in MAP sensor reading on the scan tool, replace MAP sensor.
The OBD2 Code Information Be Applicable For Volkswagen:
2013 Volkswagen e-Co-Motion Concept,2013 Volkswagen Up 4-door,2013 Volkswagen Up,2013 Volkswagen Touareg Edition X,2013 Volkswagen Scirocco GTS,2013 Volkswagen Santana,2013 Volkswagen Polo R WRC,2013 Volkswagen Polo BlueGT,2013 Volkswagen Passat Alltrack,2013 Volkswagen Lavida,2013 Volkswagen Kombi Last Edition,2013 Volkswagen Jetta Hybrid,2013 Volkswagen Golf Sportsvan Concept,2013 Volkswagen Golf Plus Life,2013 Volkswagen Golf Mk VII UK-Version,2013 Volkswagen Golf GTI Cabriolet,2013 Volkswagen Golf,2013 Volkswagen Gol 2-door,2013 Volkswagen Eco Up,2013 Volkswagen Caddy Cross,2012 Volkswagen Tiguan,2012 Volkswagen Jetta GLI,2012 Volkswagen Beetle,2011 Volkswagen eT Concept,2011 Volkswagen e-Up Concept,2011 Volkswagen XL1 Concept,2011 Volkswagen Touran,2011 Volkswagen Touareg,2011 Volkswagen Sharan,2011 Volkswagen Polo GTI,2011 Volkswagen Phaeton,2011 Volkswagen Jetta,2011 Volkswagen Eos,2011 Volkswagen CrossTouran,2011 Volkswagen CrossPolo,2011 Volkswagen CrossGolf,2011 Volkswagen Amarok,2010 Volkswagen Polo,2010 Volkswagen Golf,2009 Volkswagen Phaeton,2009 Volkswagen Golf,2009 Volkswagen Gol,2008 Volkswagen Phaeton,2008 Volkswagen Golf Variant,2008 Volkswagen Golf GTI Concept,2008 Volkswagen Golf BlueMotion,2007 Volkswagen Up Concept,2007 Volkswagen Touran,2007 Volkswagen Touareg,2007 Volkswagen Eos,2006 Volkswagen Rabbit,2006 Volkswagen Passat,2006 Volkswagen Jetta,2006 Volkswagen Eos,2006 Volkswagen CrossPolo,2005 Volkswagen Touareg,2005 Volkswagen Golf,2005 Volkswagen Fox,2004 Volkswagen RaceTouareg,2004 Volkswagen Golf,2004 Volkswagen Concept T,2004 Volkswagen Concept C,2003 Volkswagen Touran,2003 Volkswagen Passat
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Volkswagen makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.