Description
OBD-II Trouble Code Description for P0341 Volkswagen
Camshaft Position Sensor “A” Circuit Range/Performance
What does this mean?
OBD2 Code P0341 Volkswagen definition:
This P0341 Volkswagen code basically means that the powertrain control module (PCM) detected a problem with the camshaft signal. The camshaft position sensor (CPS) sends a specific signal to the PCM for Top Dead Center on the compression stroke as well as signals indicating the position of the cam sensor. This is accomplished through a reluctor wheel attached to the camshaft that passes by the cam sensor. Any time that the signal to the PCM is inconsistent with what the signal should be, this code is set. NOTE: this code can also be set by extended cranking periods.
Symptoms
Possible sumptoms of OBD code P0341 Volkswagen
The car will likely run with this code set, as it is often intermittent and also because the PCM can often operate the vehicle in “limp-in/limp-home” mode even with a cam sensor signal problem. There may be no noticeable symptoms other than: Poor fuel economy (if engine runs) Possible no start condition
Causes
Possible causes of OBD code P0341 Volkswagen
A code P0341 Volkswagen may mean that one or more of the following has happened: Cam sensor wiring routed too close to spark plug wiring (causing interference) Poor wiring connection at cam sensor Poor wiring connection at PCM Bad cam sensor Damaged reluctor wheel
Possible Solutions
Often relacing the sensor fixes this code, but not necessarily. Therefore it’s important to check the following: Check that the wiring isn’t routed too close to any secondary ignition components (coil, spark plug wires, etc.) Visually inspect the wiring at the sensor for any burn marks, discoloration indicative of melting or chafing Visually inspect the cam sensor for damage Visually inspect the reluctor wheel through the cam sensor port (if possible) for any missing teeth or any damage If reluctor isn’t visible from outside the engine, visual test can only be done by removing cam shaft or intake manifold (depending on engine design) If all checks out okay, then replace the sensor. Related Camshaft Trouble Codes: P0340 Volkswagen
The OBD2 Code Information Be Applicable For Volkswagen:
2013 Volkswagen e-Co-Motion Concept,2013 Volkswagen Up 4-door,2013 Volkswagen Up,2013 Volkswagen Touareg Edition X,2013 Volkswagen Scirocco GTS,2013 Volkswagen Santana,2013 Volkswagen Polo R WRC,2013 Volkswagen Polo BlueGT,2013 Volkswagen Passat Alltrack,2013 Volkswagen Lavida,2013 Volkswagen Kombi Last Edition,2013 Volkswagen Jetta Hybrid,2013 Volkswagen Golf Sportsvan Concept,2013 Volkswagen Golf Plus Life,2013 Volkswagen Golf Mk VII UK-Version,2013 Volkswagen Golf GTI Cabriolet,2013 Volkswagen Golf,2013 Volkswagen Gol 2-door,2013 Volkswagen Eco Up,2013 Volkswagen Caddy Cross,2012 Volkswagen Tiguan,2012 Volkswagen Jetta GLI,2012 Volkswagen Beetle,2011 Volkswagen eT Concept,2011 Volkswagen e-Up Concept,2011 Volkswagen XL1 Concept,2011 Volkswagen Touran,2011 Volkswagen Touareg,2011 Volkswagen Sharan,2011 Volkswagen Polo GTI,2011 Volkswagen Phaeton,2011 Volkswagen Jetta,2011 Volkswagen Eos,2011 Volkswagen CrossTouran,2011 Volkswagen CrossPolo,2011 Volkswagen CrossGolf,2011 Volkswagen Amarok,2010 Volkswagen Polo,2010 Volkswagen Golf,2009 Volkswagen Phaeton,2009 Volkswagen Golf,2009 Volkswagen Gol,2008 Volkswagen Phaeton,2008 Volkswagen Golf Variant,2008 Volkswagen Golf GTI Concept,2008 Volkswagen Golf BlueMotion,2007 Volkswagen Up Concept,2007 Volkswagen Touran,2007 Volkswagen Touareg,2007 Volkswagen Eos,2006 Volkswagen Rabbit,2006 Volkswagen Passat,2006 Volkswagen Jetta,2006 Volkswagen Eos,2006 Volkswagen CrossPolo,2005 Volkswagen Touareg,2005 Volkswagen Golf,2005 Volkswagen Fox,2004 Volkswagen RaceTouareg,2004 Volkswagen Golf,2004 Volkswagen Concept T,2004 Volkswagen Concept C,2003 Volkswagen Touran,2003 Volkswagen Passat
Note:
1. The list of automotive Makes at the right edge of the screen. The currently selected ODB-ii codes is for the Volkswagen makes.
2. Look up the other OBD II Trouble Codes, please use the search box. Enter the 5 character trouble codes in the search box and submit the search.
3. Don’t assume a particular OBD-II code means the same for other auto manufacturers as there are many makes specific codes in use.
4. If your OBD-II trouble codes are for a different car, select that vehicle series before searching for the diagnostic codes because not all OBD2 codes used by one manufacture are used by the other makes.
5. The information contained on this site is presented for informational purposes only. We are not responsible for any actions you take on your vehicle. If you have any doubt as to repairs on your vehicle, please contact your technician.